{"product_id":"500gb-western-digital-wdc-wd5003abyx-18wera0-smart_error_count-5","title":"500GB Western Digital, WDC WD5003ABYX-18WERA0, (smart_error_count=5)","description":"\u003cp\u003e500GB, Western Digital WDC WD5003ABYX-18WERA0, used hard drive, 7200 RPM, SATA 2.6, 3.0 Gb\/s, with 55853 powered-on hours.\u003c\/p\u003e\n\n\u003cp\u003eDiagnostic notes: smart_error_count=5. Review the recorded results below before purchase.\u003c\/p\u003e\n\n\u003ch2\u003eImportant notes\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eThis drive weighs 462 grams.\u003c\/li\u003e\n\u003cli\u003ePending sectors: 0\u003c\/li\u003e\n\u003cli\u003eReallocated sectors: 0\u003c\/li\u003e\n\u003cli\u003eLogged SMART errors: 5\u003c\/li\u003e\n\u003cli\u003eCRC errors: 0\u003c\/li\u003e\n\u003cli\u003espin_retry_count: 0\u003c\/li\u003e\n\u003cli\u003eReallocation events: 0\u003c\/li\u003e\n\u003cli\u003eOffline uncorrectable sectors: 0\u003c\/li\u003e\n\u003cli\u003ePower cycles: 104\u003c\/li\u003e\n\u003cli\u003eLoad cycles: 15\u003c\/li\u003e\n\u003cli\u003eSMART overall health: PASSED\u003c\/li\u003e\n\u003cli\u003eLatest Extended offline self-test: Completed without error\u003c\/li\u003e\n\u003cli\u003eBadblocks was run using the standard four-pass pattern test, and 0 bad blocks were found.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eYou will receive this specific drive, identified in this listing as serial WD-WMAYP6618215.\u003c\/p\u003e\n\n\u003cp\u003eThis used drive is sold 'as is', with no warranty on its functionality. I do warrant that the testing described in this listing was actually performed on this specific drive and that the SMART output reproduced below is the output obtained from this drive. In general, SMART data can be erased or tampered with, for example to reset the reported powered-on hours to zero. I certify that I have not erased, reset, or otherwise tampered with this drive's SMART data, but I cannot certify that a previous owner has not done so.\u003c\/p\u003e\n\n\u003cp\u003eCounters such as powered-on hours and power-cycle counts may differ slightly from the recorded output because the drive may have been powered on again between the time the SMART output was captured and packaging for shipment.\u003c\/p\u003e\n\n\u003ch2\u003eRecorded fio performance tests\u003c\/h2\u003e\n\n\u003cp\u003eThese tests were performed over a USB interface. The demonstrated transfer speeds may be artificially limited by the USB 3 interface.\u003c\/p\u003e\n\n\u003cpre\u003eSEQUENTIAL READ: bw=130MiB\/s (136MB\/s)\nSEQUENTIAL WRITE: bw=129MiB\/s (136MB\/s)\nRANDOM READ: bw=321KiB\/s (329kB\/s)\nRANDOM WRITE: bw=746KiB\/s (764kB\/s)\nRANDOM READ (Queue Depth=1): bw=315KiB\/s (322kB\/s)\u003c\/pre\u003e\n\n\u003ch2\u003eOutput from fdisk -l \/dev\/sdd\u003c\/h2\u003e\n\n\u003cpre\u003eDisk \/dev\/sdd: 465.76 GiB, 500107862016 bytes, 976773168 sectors\nDisk model: USB3.0 DISK02   \nUnits: sectors of 1 * 512 = 512 bytes\nSector size (logical\/physical): 512 bytes \/ 512 bytes\nI\/O size (minimum\/optimal): 512 bytes \/ 512 bytes\n\u003c\/pre\u003e\n\n\u003ch2\u003eOutput from hdparm -I \/dev\/sdd\u003c\/h2\u003e\n\n\u003cpre\u003e\n\/dev\/sdd:\n\nATA device, with non-removable media\n\tModel Number:       WDC WD5003ABYX-18WERA0                  \n\tSerial Number:      WD-WMAYP6618215\n\tFirmware Revision:  01.01S03\n\tTransport:          Serial, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6\nStandards:\n\tSupported: 8 7 6 5 \n\tLikely used: 8\nConfiguration:\n\tLogical\t\tmax\tcurrent\n\tcylinders\t16383\t16383\n\theads\t\t16\t16\n\tsectors\/track\t63\t63\n\t--\n\tCHS current addressable sectors:    16514064\n\tLBA    user addressable sectors:   268435455\n\tLBA48  user addressable sectors:   976773168\n\tLogical\/Physical Sector size:           512 bytes\n\tdevice size with M = 1024*1024:      476940 MBytes\n\tdevice size with M = 1000*1000:      500107 MBytes (500 GB)\n\tcache\/buffer size  = unknown\n\tNominal Media Rotation Rate: 7200\nCapabilities:\n\tLBA, IORDY(can be disabled)\n\tQueue depth: 32\n\tStandby timer values: spec'd by Standard, with device specific minimum\n\tR\/W multiple sector transfer: Max = 16\tCurrent = 0\n\tAdvanced power management level: 128\n\tDMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 \n\t     Cycle time: min=120ns recommended=120ns\n\tPIO: pio0 pio1 pio2 pio3 pio4 \n\t     Cycle time: no flow control=120ns  IORDY flow control=120ns\nCommands\/features:\n\tEnabled\tSupported:\n\t   *\tSMART feature set\n\t    \tSecurity Mode feature set\n\t   *\tPower Management feature set\n\t   *\tWrite cache\n\t   *\tLook-ahead\n\t   *\tHost Protected Area feature set\n\t   *\tWRITE_BUFFER command\n\t   *\tREAD_BUFFER command\n\t   *\tNOP cmd\n\t   *\tDOWNLOAD_MICROCODE\n\t   *\tAdvanced Power Management feature set\n\t    \tPower-Up In Standby feature set\n\t   *\tSET_FEATURES required to spinup after power up\n\t    \tSET_MAX security extension\n\t   *\t48-bit Address feature set\n\t   *\tDevice Configuration Overlay feature set\n\t   *\tMandatory FLUSH_CACHE\n\t   *\tFLUSH_CACHE_EXT\n\t   *\tSMART error logging\n\t   *\tSMART self-test\n\t   *\tGeneral Purpose Logging feature set\n\t   *\tWRITE_{DMA|MULTIPLE}_FUA_EXT\n\t   *\t64-bit World wide name\n\t   *\tIDLE_IMMEDIATE with UNLOAD\n\t   *\tWRITE_UNCORRECTABLE_EXT command\n\t   *\t{READ,WRITE}_DMA_EXT_GPL commands\n\t   *\tSegmented DOWNLOAD_MICROCODE\n\t   *\tGen1 signaling speed (1.5Gb\/s)\n\t   *\tGen2 signaling speed (3.0Gb\/s)\n\t   *\tNative Command Queueing (NCQ)\n\t   *\tPhy event counters\n\t   *\tIdle-Unload when NCQ is active\n\t   *\tNCQ priority information\n\t    \tDMA Setup Auto-Activate optimization\n\t   *\tSoftware settings preservation\n\t   *\tSMART Command Transport (SCT) feature set\n\t   *\tSCT Read\/Write Long (AC1), obsolete\n\t   *\tSCT Write Same (AC2)\n\t   *\tSCT Error Recovery Control (AC3)\n\t   *\tSCT Features Control (AC4)\n\t   *\tSCT Data Tables (AC5)\n\t    \tunknown 206[12] (vendor specific)\n\t    \tunknown 206[13] (vendor specific)\nSecurity: \n\tMaster password revision code = 65534\n\t\tsupported\n\tnot\tenabled\n\tnot\tlocked\n\tnot\tfrozen\n\tnot\texpired: security count\n\t\tsupported: enhanced erase\n\t82min for SECURITY ERASE UNIT. 82min for ENHANCED SECURITY ERASE UNIT.\nLogical Unit WWN Device Identifier: 50014ee0ae4f8625\n\tNAA\t\t: 5\n\tIEEE OUI\t: 0014ee\n\tUnique ID\t: 0ae4f8625\nChecksum: correct\n\u003c\/pre\u003e\n\n\u003ch2\u003eOutput from smartctl -x \/dev\/sdd\u003c\/h2\u003e\n\n\u003cpre\u003esmartctl 7.5 2025-04-30 r5714 [x86_64-linux-7.0.0-31-generic] (local build)\nCopyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org\n\n=== START OF INFORMATION SECTION ===\nModel Family:     Western Digital RE4\nDevice Model:     WDC WD5003ABYX-18WERA0\nSerial Number:    WD-WMAYP6618215\nLU WWN Device Id: 5 0014ee 0ae4f8625\nAdd. Product Id:  DELL(tm)\nFirmware Version: 01.01S03\nUser Capacity:    500,107,862,016 bytes [500 GB]\nSector Size:      512 bytes logical\/physical\nRotation Rate:    7200 rpm\nDevice is:        In smartctl database 7.5\/5706\nATA Version is:   ATA8-ACS (minor revision not indicated)\nSATA Version is:  SATA 2.6, 3.0 Gb\/s\nLocal Time is:    Tue Sep 15 03:03:27 2026 UTC\nSMART support is: Available - device has SMART capability.\nSMART support is: Enabled\nAAM feature is:   Unavailable\nAPM level is:     128 (minimum power consumption without standby)\nRd look-ahead is: Enabled\nWrite cache is:   Enabled\nDSN feature is:   Unavailable\nATA Security is:  Disabled, NOT FROZEN [SEC1]\n\n=== START OF READ SMART DATA SECTION ===\nSMART Status not supported: Incomplete response, ATA output registers missing\nSMART overall-health self-assessment test result: PASSED\nWarning: This result is based on an Attribute check.\n\nGeneral SMART Values:\nOffline data collection status:  (0x82)\tOffline data collection activity\n\t\t\t\t\twas completed without error.\n\t\t\t\t\tAuto Offline Data Collection: Enabled.\nSelf-test execution status:      (   0)\tThe previous self-test routine completed\n\t\t\t\t\twithout error or no self-test has ever \n\t\t\t\t\tbeen run.\nTotal time to complete Offline \ndata collection: \t\t( 8160) seconds.\nOffline data collection\ncapabilities: \t\t\t (0x7b) SMART execute Offline immediate.\n\t\t\t\t\tAuto Offline data collection on\/off support.\n\t\t\t\t\tSuspend Offline collection upon new\n\t\t\t\t\tcommand.\n\t\t\t\t\tOffline surface scan supported.\n\t\t\t\t\tSelf-test supported.\n\t\t\t\t\tConveyance Self-test supported.\n\t\t\t\t\tSelective Self-test supported.\nSMART capabilities:            (0x0003)\tSaves SMART data before entering\n\t\t\t\t\tpower-saving mode.\n\t\t\t\t\tSupports SMART auto save timer.\nError logging capability:        (0x01)\tError logging supported.\n\t\t\t\t\tGeneral Purpose Logging supported.\nShort self-test routine \nrecommended polling time: \t (   2) minutes.\nExtended self-test routine\nrecommended polling time: \t (  87) minutes.\nConveyance self-test routine\nrecommended polling time: \t (   5) minutes.\nSCT capabilities: \t       (0x303f)\tSCT Status supported.\n\t\t\t\t\tSCT Error Recovery Control supported.\n\t\t\t\t\tSCT Feature Control supported.\n\t\t\t\t\tSCT Data Table supported.\n\nSMART Attributes Data Structure revision number: 16\nVendor Specific SMART Attributes with Thresholds:\nID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE\n  1 Raw_Read_Error_Rate     POSR-K   200   200   051    -    40\n  3 Spin_Up_Time            POS--K   141   137   021    -    3916\n  4 Start_Stop_Count        -O--CK   100   100   000    -    119\n  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0\n  7 Seek_Error_Rate         -OSR-K   200   200   000    -    0\n  9 Power_On_Hours          -O--CK   024   024   000    -    55853\n 10 Spin_Retry_Count        -O--CK   100   100   000    -    0\n 11 Calibration_Retry_Count -O--CK   100   100   000    -    0\n 12 Power_Cycle_Count       -O--CK   100   100   000    -    104\n192 Power-Off_Retract_Count -O--CK   200   200   000    -    103\n193 Load_Cycle_Count        -O--CK   200   200   000    -    15\n194 Temperature_Celsius     -O---K   106   102   000    -    37 (Min\/Max 23\/42)\n196 Reallocated_Event_Count -O--CK   200   200   000    -    0\n197 Current_Pending_Sector  -O--CK   200   200   000    -    0\n198 Offline_Uncorrectable   ----CK   200   200   000    -    0\n199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0\n200 Multi_Zone_Error_Rate   ---R--   200   200   000    -    0\n                            ||||||_ K auto-keep\n                            |||||__ C event count\n                            ||||___ R error rate\n                            |||____ S speed\/performance\n                            ||_____ O updated online\n                            |______ P prefailure warning\n\nGeneral Purpose Log Directory Version 1\nSMART           Log Directory Version 1 [multi-sector log support]\nAddress    Access  R\/W   Size  Description\n0x00       GPL,SL  R\/O      1  Log Directory\n0x01           SL  R\/O      1  Summary SMART error log\n0x02           SL  R\/O      5  Comprehensive SMART error log\n0x03       GPL     R\/O      6  Ext. Comprehensive SMART error log\n0x06           SL  R\/O      1  SMART self-test log\n0x07       GPL     R\/O      1  Extended self-test log\n0x09           SL  R\/W      1  Selective self-test log\n0x10       GPL     R\/O      1  NCQ Command Error log\n0x11       GPL     R\/O      1  SATA Phy Event Counters log\n0x80-0x9f  GPL,SL  R\/W     16  Host vendor specific log\n0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log\n0xa8-0xb5  GPL,SL  VS       1  Device vendor specific log\n0xb6       GPL     VS       1  Device vendor specific log\n0xb7       GPL,SL  VS       1  Device vendor specific log\n0xbd       GPL,SL  VS       1  Device vendor specific log\n0xc0       GPL,SL  VS       1  Device vendor specific log\n0xc1       GPL     VS      24  Device vendor specific log\n0xe0       GPL,SL  R\/W      1  SCT Command\/Status\n0xe1       GPL,SL  R\/W      1  SCT Data Transfer\n\nSMART Extended Comprehensive Error Log Version: 1 (6 sectors)\nDevice Error Count: 5\n\tCR     = Command Register\n\tFEATR  = Features Register\n\tCOUNT  = Count (was: Sector Count) Register\n\tLBA_48 = Upper bytes of LBA High\/Mid\/Low Registers ]  ATA-8\n\tLH     = LBA High (was: Cylinder High) Register    ]   LBA\n\tLM     = LBA Mid (was: Cylinder Low) Register      ] Register\n\tLL     = LBA Low (was: Sector Number) Register     ]\n\tDV     = Device (was: Device\/Head) Register\n\tDC     = Device Control Register\n\tER     = Error register\n\tST     = Status register\nPowered_Up_Time is measured from power on, and printed as\nDDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,\nSS=sec, and sss=millisec. It \"wraps\" after 49.710 days.\n\nError 5 [4] occurred at disk power-on lifetime: 43315 hours (1804 days + 19 hours)\n  When the command that caused the error occurred, the device was active or idle.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 51 02 80 00 00 18 08 9a bc 40 00  Error: UNC at LBA = 0x18089abc = 403217084\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  60 02 80 00 00 00 00 18 08 98 d2 40 00     17:41:02.285  READ FPDMA QUEUED\n  60 02 80 00 00 00 00 18 08 96 52 40 00     17:41:02.282  READ FPDMA QUEUED\n  60 02 80 00 00 00 00 18 08 93 d2 40 00     17:41:02.280  READ FPDMA QUEUED\n  60 02 80 00 00 00 00 18 08 91 52 40 00     17:41:02.276  READ FPDMA QUEUED\n  60 02 80 00 00 00 00 18 08 8e d2 40 00     17:41:02.274  READ FPDMA QUEUED\n\nError 4 [3] occurred at disk power-on lifetime: 38308 hours (1596 days + 4 hours)\n  When the command that caused the error occurred, the device was active or idle.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 51 00 08 00 00 16 38 89 2c 40 00  Error: UNC at LBA = 0x1638892c = 372803884\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  60 00 08 00 00 00 00 16 38 89 2a 40 00     06:19:22.635  READ FPDMA QUEUED\n  60 00 08 00 00 00 00 16 3a 82 da 40 00     06:19:22.635  READ FPDMA QUEUED\n  60 00 90 00 08 00 00 17 2a 88 82 40 00     06:19:22.611  READ FPDMA QUEUED\n  60 00 80 00 00 00 00 17 2a 88 02 40 00     06:19:22.611  READ FPDMA QUEUED\n  60 00 08 00 08 00 00 17 2a 87 fa 40 00     06:19:22.601  READ FPDMA QUEUED\n\nError 3 [2] occurred at disk power-on lifetime: 38308 hours (1596 days + 4 hours)\n  When the command that caused the error occurred, the device was active or idle.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 51 00 08 00 00 15 4c 87 b6 40 00  Error: UNC at LBA = 0x154c87b6 = 357337014\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  60 00 08 00 00 00 00 15 4c 87 b2 40 00     06:16:51.056  READ FPDMA QUEUED\n  60 00 04 00 00 00 00 15 4c 87 b2 40 00     06:16:51.040  READ FPDMA QUEUED\n  2f 00 00 00 01 00 00 00 00 00 10 40 00     06:16:50.981  READ LOG EXT\n  60 00 08 00 00 00 00 15 4c 87 b2 40 00     06:16:48.234  READ FPDMA QUEUED\n  60 00 80 00 08 00 00 15 65 88 7a 40 00     06:16:48.206  READ FPDMA QUEUED\n\nError 2 [1] occurred at disk power-on lifetime: 38308 hours (1596 days + 4 hours)\n  When the command that caused the error occurred, the device was active or idle.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 51 00 08 00 00 15 4c 87 b6 40 00  Error: UNC at LBA = 0x154c87b6 = 357337014\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  60 00 08 00 00 00 00 15 4c 87 b2 40 00     06:16:48.234  READ FPDMA QUEUED\n  60 00 80 00 08 00 00 15 65 88 7a 40 00     06:16:48.206  READ FPDMA QUEUED\n  60 00 80 00 00 00 00 15 65 87 fa 40 00     06:16:48.206  READ FPDMA QUEUED\n  60 00 08 00 08 00 00 15 65 87 f2 40 00     06:16:48.206  READ FPDMA QUEUED\n  60 00 40 00 00 00 00 15 65 87 b2 40 00     06:16:48.206  READ FPDMA QUEUED\n\nError 1 [0] occurred at disk power-on lifetime: 38308 hours (1596 days + 4 hours)\n  When the command that caused the error occurred, the device was active or idle.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 51 00 08 00 00 15 14 87 a7 40 00  Error: UNC at LBA = 0x151487a7 = 353666983\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  60 00 08 00 00 00 00 15 14 87 a2 40 00     06:14:53.981  READ FPDMA QUEUED\n  60 00 08 00 00 00 00 16 c0 87 b2 40 00     06:14:53.207  READ FPDMA QUEUED\n  60 00 10 00 20 00 00 1a 45 d4 02 40 00     06:14:53.171  READ FPDMA QUEUED\n  60 00 38 00 18 00 00 1a 45 8c 5a 40 00     06:14:53.171  READ FPDMA QUEUED\n  60 00 10 00 10 00 00 1a 45 4a 82 40 00     06:14:53.171  READ FPDMA QUEUED\n\nSMART Extended Self-test Log Version: 1 (1 sectors)\nNum  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error\n# 1  Extended offline    Completed without error       00%     55852         -\n# 2  Short offline       Completed without error       00%        29         -\n# 3  Extended offline    Completed without error       00%        29         -\n# 4  Short offline       Completed without error       00%        28         -\n\nSMART Selective self-test log data structure revision number 1\n SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS\n    1        0        0  Not_testing\n    2        0        0  Not_testing\n    3        0        0  Not_testing\n    4        0        0  Not_testing\n    5        0        0  Not_testing\nSelective self-test flags (0x0):\n  After scanning selected spans, do NOT read-scan remainder of disk.\nIf Selective self-test is pending on power-up, resume after 0 minute delay.\n\nSCT Status Version:                  3\nSCT Version (vendor specific):       258 (0x0102)\nDevice State:                        Active (0)\nCurrent Temperature:                    37 Celsius\nPower Cycle Min\/Max Temperature:     23\/42 Celsius\nLifetime    Min\/Max Temperature:     23\/42 Celsius\nUnder\/Over Temperature Limit Count:   0\/0\n\nSCT Temperature History Version:     2\nTemperature Sampling Period:         1 minute\nTemperature Logging Interval:        1 minute\nMin\/Max recommended Temperature:      0\/60 Celsius\nMin\/Max Temperature Limit:           -41\/85 Celsius\nTemperature History Size (Index):    478 (216)\n\nIndex    Estimated Time   Temperature Celsius\n 217    2026-09-14 19:06    38  *******************\n ...    ..(  7 skipped).    ..  *******************\n 225    2026-09-14 19:14    38  *******************\n 226    2026-09-14 19:15    39  ********************\n ...    ..(  3 skipped).    ..  ********************\n 230    2026-09-14 19:19    39  ********************\n 231    2026-09-14 19:20    40  *********************\n ...    ..( 68 skipped).    ..  *********************\n 300    2026-09-14 20:29    40  *********************\n 301    2026-09-14 20:30    41  **********************\n ...    ..(  9 skipped).    ..  **********************\n 311    2026-09-14 20:40    41  **********************\n 312    2026-09-14 20:41    40  *********************\n ...    ..(  5 skipped).    ..  *********************\n 318    2026-09-14 20:47    40  *********************\n 319    2026-09-14 20:48    39  ********************\n ...    ..( 13 skipped).    ..  ********************\n 333    2026-09-14 21:02    39  ********************\n 334    2026-09-14 21:03    38  *******************\n ...    ..( 25 skipped).    ..  *******************\n 360    2026-09-14 21:29    38  *******************\n 361    2026-09-14 21:30    37  ******************\n ...    ..( 14 skipped).    ..  ******************\n 376    2026-09-14 21:45    37  ******************\n 377    2026-09-14 21:46    38  *******************\n ...    ..(141 skipped).    ..  *******************\n  41    2026-09-15 00:08    38  *******************\n  42    2026-09-15 00:09    37  ******************\n ...    ..(152 skipped).    ..  ******************\n 195    2026-09-15 02:42    37  ******************\n 196    2026-09-15 02:43    38  *******************\n ...    ..(  2 skipped).    ..  *******************\n 199    2026-09-15 02:46    38  *******************\n 200    2026-09-15 02:47    39  ********************\n ...    ..(  4 skipped).    ..  ********************\n 205    2026-09-15 02:52    39  ********************\n 206    2026-09-15 02:53    38  *******************\n ...    ..(  9 skipped).    ..  *******************\n 216    2026-09-15 03:03    38  *******************\n\nSMART WRITE LOG does not return COUNT and LBA_LOW register\nSCT (Get) Error Recovery Control command failed\n\nDevice Statistics (GP\/SMART Log 0x04) not supported\n\nPending Defects log (GP Log 0x0c) not supported\n\nSATA Phy Event Counters (GP Log 0x11)\nID      Size     Value  Description\n0x0001  2            0  Command failed due to ICRC error\n0x0002  2            0  R_ERR response for data FIS\n0x0003  2            0  R_ERR response for device-to-host data FIS\n0x0004  2            0  R_ERR response for host-to-device data FIS\n0x0005  2            0  R_ERR response for non-data FIS\n0x0006  2            0  R_ERR response for device-to-host non-data FIS\n0x0007  2            0  R_ERR response for host-to-device non-data FIS\n0x000a  2           13  Device-to-host register FISes sent due to a COMRESET\n0x000b  2            0  CRC errors within host-to-device FIS\n0x8000  4       282290  Vendor specific\n\n\u003c\/pre\u003e\n","brand":"Robert Elder Software Inc's Store","offers":[{"title":"Default Title","offer_id":67628253806880,"sku":"2026-10-01-WD-WMAYP6618215","price":8.35,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0966\/8945\/5392\/files\/f4f16ba3-a368-4cfc-ae0d-8fd0667029b0.jpg?v=1790951179","url":"https:\/\/shopify.robertelder.org\/products\/500gb-western-digital-wdc-wd5003abyx-18wera0-smart_error_count-5","provider":"Robert Elder Software Inc's Store","version":"1.0","type":"link"}