{"product_id":"500gb-western-digital-wdc-wd5000ys-01mpb0-smart-fail","title":"500GB Western Digital, WDC WD5000YS-01MPB0, (SMART FAIL)","description":"\u003cp\u003e500GB, Western Digital WDC WD5000YS-01MPB0, used hard drive, with 6632 powered-on hours.\u003c\/p\u003e\n\n\u003cp\u003eThis drive has a failed SMART health assessment or self-test. It is offered for parts or repair, not as reliable storage.\u003c\/p\u003e\n\n\u003ch2\u003eImportant notes\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eThis drive weighs 701 grams.\u003c\/li\u003e\n\u003cli\u003ePending sectors: 59\u003c\/li\u003e\n\u003cli\u003eReallocated sectors: 0\u003c\/li\u003e\n\u003cli\u003eLogged SMART errors: 433\u003c\/li\u003e\n\u003cli\u003eCRC errors: 0\u003c\/li\u003e\n\u003cli\u003espin_retry_count: 0\u003c\/li\u003e\n\u003cli\u003eReallocation events: 0\u003c\/li\u003e\n\u003cli\u003eOffline uncorrectable sectors: 0\u003c\/li\u003e\n\u003cli\u003ePower cycles: 582\u003c\/li\u003e\n\u003cli\u003eSMART overall health: PASSED\u003c\/li\u003e\n\u003cli\u003eLatest Extended offline self-test: Completed: read failure\u003c\/li\u003e\n\u003cli\u003eBadblocks log: 307 bad-block entries.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eYou will receive this specific drive, identified in this listing as serial WD-WMANU1372965.\u003c\/p\u003e\n\n\u003cp\u003eThis used drive is sold 'as is', with no warranty on its functionality. I do warrant that the testing described in this listing was actually performed on this specific drive and that the SMART output reproduced below is the output obtained from this drive. In general, SMART data can be erased or tampered with, for example to reset the reported powered-on hours to zero. I certify that I have not erased, reset, or otherwise tampered with this drive's SMART data, but I cannot certify that a previous owner has not done so.\u003c\/p\u003e\n\n\u003cp\u003eCounters such as powered-on hours and power-cycle counts may differ slightly from the recorded output because the drive may have been powered on again between the time the SMART output was captured and packaging for shipment.\u003c\/p\u003e\n\n\u003ch2\u003eRecorded fio performance tests\u003c\/h2\u003e\n\n\u003cp\u003eThese tests were performed over a USB interface. The demonstrated transfer speeds may be artificially limited by the USB 3 interface.\u003c\/p\u003e\n\n\u003cpre\u003eSEQUENTIAL READ: bw=70.0MiB\/s (73.4MB\/s)\nSEQUENTIAL WRITE: bw=69.9MiB\/s (73.3MB\/s)\nRANDOM READ: bw=291KiB\/s (298kB\/s)\nRANDOM WRITE: bw=549KiB\/s (563kB\/s)\nRANDOM READ (Queue Depth=1): bw=286KiB\/s (293kB\/s)\u003c\/pre\u003e\n\n\u003ch2\u003eOutput from fdisk -l \/dev\/sdf\u003c\/h2\u003e\n\n\u003cpre\u003eDisk \/dev\/sdf: 465.76 GiB, 500107862016 bytes, 976773168 sectors\nDisk model: USB3.0 DISK04   \nUnits: sectors of 1 * 512 = 512 bytes\nSector size (logical\/physical): 512 bytes \/ 512 bytes\nI\/O size (minimum\/optimal): 512 bytes \/ 512 bytes\n\u003c\/pre\u003e\n\n\u003ch2\u003eOutput from hdparm -I \/dev\/sdf\u003c\/h2\u003e\n\n\u003cpre\u003e\n\/dev\/sdf:\n\nATA device, with non-removable media\n\tModel Number:       WDC WD5000YS-01MPB0                     \n\tSerial Number:      WD-WMANU1372965\n\tFirmware Revision:  09.02E09\nStandards:\n\tSupported: 7 6 5 4 \n\tLikely used: 8\nConfiguration:\n\tLogical\t\tmax\tcurrent\n\tcylinders\t16383\t16383\n\theads\t\t16\t16\n\tsectors\/track\t63\t63\n\t--\n\tCHS current addressable sectors:    16514064\n\tLBA    user addressable sectors:   268435455\n\tLBA48  user addressable sectors:   976773168\n\tLogical\/Physical Sector size:           512 bytes\n\tdevice size with M = 1024*1024:      476940 MBytes\n\tdevice size with M = 1000*1000:      500107 MBytes (500 GB)\n\tcache\/buffer size  = 16384 KBytes\nCapabilities:\n\tLBA, IORDY(can be disabled)\n\tQueue depth: 32\n\tStandby timer values: spec'd by Standard, with device specific minimum\n\tR\/W multiple sector transfer: Max = 16\tCurrent = 0\n\tRecommended acoustic management value: 128, current value: 254\n\tDMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 \n\t     Cycle time: min=120ns recommended=120ns\n\tPIO: pio0 pio1 pio2 pio3 pio4 \n\t     Cycle time: no flow control=120ns  IORDY flow control=120ns\nCommands\/features:\n\tEnabled\tSupported:\n\t   *\tSMART feature set\n\t    \tSecurity Mode feature set\n\t   *\tPower Management feature set\n\t   *\tWrite cache\n\t   *\tLook-ahead\n\t   *\tHost Protected Area feature set\n\t   *\tWRITE_BUFFER command\n\t   *\tREAD_BUFFER command\n\t   *\tNOP cmd\n\t   *\tDOWNLOAD_MICROCODE\n\t    \tPower-Up In Standby feature set\n\t   *\tSET_FEATURES required to spinup after power up\n\t    \tSET_MAX security extension\n\t    \tAutomatic Acoustic Management feature set\n\t   *\t48-bit Address feature set\n\t   *\tDevice Configuration Overlay feature set\n\t   *\tMandatory FLUSH_CACHE\n\t   *\tFLUSH_CACHE_EXT\n\t   *\tSMART error logging\n\t   *\tSMART self-test\n\t   *\tGeneral Purpose Logging feature set\n\t   *\tWRITE_{DMA|MULTIPLE}_FUA_EXT\n\t   *\t64-bit World wide name\n\t   *\tGen1 signaling speed (1.5Gb\/s)\n\t   *\tGen2 signaling speed (3.0Gb\/s)\n\t   *\tNative Command Queueing (NCQ)\n\t   *\tHost-initiated interface power management\n\t   *\tPhy event counters\n\t    \tDMA Setup Auto-Activate optimization\n\t   *\tSoftware settings preservation\n\t   *\tSMART Command Transport (SCT) feature set\n\t   *\tSCT Read\/Write Long (AC1), obsolete\n\t   *\tSCT Write Same (AC2)\n\t   *\tSCT Error Recovery Control (AC3)\n\t   *\tSCT Features Control (AC4)\n\t   *\tSCT Data Tables (AC5)\n\t    \tunknown 206[12] (vendor specific)\nSecurity: \n\tMaster password revision code = 65534\n\t\tsupported\n\tnot\tenabled\n\tnot\tlocked\n\tnot\tfrozen\n\tnot\texpired: security count\n\tnot\tsupported: enhanced erase\n\t138min for SECURITY ERASE UNIT.\nLogical Unit WWN Device Identifier: 50014ee0aaac98d9\n\tNAA\t\t: 5\n\tIEEE OUI\t: 0014ee\n\tUnique ID\t: 0aaac98d9\nChecksum: correct\n\u003c\/pre\u003e\n\n\u003ch2\u003eOutput from smartctl -x \/dev\/sdf\u003c\/h2\u003e\n\n\u003cpre\u003esmartctl 7.5 2025-04-30 r5714 [x86_64-linux-7.0.0-31-generic] (local build)\nCopyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org\n\n=== START OF INFORMATION SECTION ===\nModel Family:     Western Digital RE2 Serial ATA\nDevice Model:     WDC WD5000YS-01MPB0\nSerial Number:    WD-WMANU1372965\nLU WWN Device Id: 5 0014ee 0aaac98d9\nFirmware Version: 09.02E09\nUser Capacity:    500,107,862,016 bytes [500 GB]\nSector Size:      512 bytes logical\/physical\nDevice is:        In smartctl database 7.5\/5706\nATA Version is:   ATA\/ATAPI-7 (minor revision not indicated)\nLocal Time is:    Sat Sep 19 22:28:29 2026 UTC\nSMART support is: Available - device has SMART capability.\nSMART support is: Enabled\nAAM feature is:   Disabled\nAPM feature is:   Unavailable\nRd look-ahead is: Enabled\nWrite cache is:   Enabled\nDSN feature is:   Unavailable\nATA Security is:  Disabled, NOT FROZEN [SEC1]\n\n=== START OF READ SMART DATA SECTION ===\nSMART Status not supported: Incomplete response, ATA output registers missing\nSMART overall-health self-assessment test result: PASSED\nWarning: This result is based on an Attribute check.\n\nGeneral SMART Values:\nOffline data collection status:  (0x00)\tOffline data collection activity\n\t\t\t\t\twas never started.\n\t\t\t\t\tAuto Offline Data Collection: Disabled.\nSelf-test execution status:      ( 121)\tThe previous self-test completed having\n\t\t\t\t\tthe read element of the test failed.\nTotal time to complete Offline \ndata collection: \t\t(13560) seconds.\nOffline data collection\ncapabilities: \t\t\t (0x7b) SMART execute Offline immediate.\n\t\t\t\t\tAuto Offline data collection on\/off support.\n\t\t\t\t\tSuspend Offline collection upon new\n\t\t\t\t\tcommand.\n\t\t\t\t\tOffline surface scan supported.\n\t\t\t\t\tSelf-test supported.\n\t\t\t\t\tConveyance Self-test supported.\n\t\t\t\t\tSelective Self-test supported.\nSMART capabilities:            (0x0003)\tSaves SMART data before entering\n\t\t\t\t\tpower-saving mode.\n\t\t\t\t\tSupports SMART auto save timer.\nError logging capability:        (0x01)\tError logging supported.\n\t\t\t\t\tGeneral Purpose Logging supported.\nShort self-test routine \nrecommended polling time: \t (   2) minutes.\nExtended self-test routine\nrecommended polling time: \t ( 170) minutes.\nConveyance self-test routine\nrecommended polling time: \t (   6) minutes.\nSCT capabilities: \t       (0x103f)\tSCT Status supported.\n\t\t\t\t\tSCT Error Recovery Control supported.\n\t\t\t\t\tSCT Feature Control supported.\n\t\t\t\t\tSCT Data Table supported.\n\nSMART Attributes Data Structure revision number: 16\nVendor Specific SMART Attributes with Thresholds:\nID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE\n  1 Raw_Read_Error_Rate     POSR--   195   194   051    -    1087\n  3 Spin_Up_Time            PO----   217   214   021    -    6141\n  4 Start_Stop_Count        -O--CK   100   100   000    -    588\n  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0\n  7 Seek_Error_Rate         POSR--   200   200   051    -    0\n  9 Power_On_Hours          -O--CK   091   091   000    -    6632\n 10 Spin_Retry_Count        PO--C-   100   100   051    -    0\n 11 Calibration_Retry_Count -O--C-   100   100   051    -    0\n 12 Power_Cycle_Count       -O--CK   100   100   000    -    582\n194 Temperature_Celsius     -O---K   109   107   000    -    43\n196 Reallocated_Event_Count -O--CK   200   200   000    -    0\n197 Current_Pending_Sector  -O--C-   200   200   000    -    59\n198 Offline_Uncorrectable   ----C-   100   253   000    -    0\n199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    0\n200 Multi_Zone_Error_Rate   P--R--   100   253   051    -    0\n                            ||||||_ K auto-keep\n                            |||||__ C event count\n                            ||||___ R error rate\n                            |||____ S speed\/performance\n                            ||_____ O updated online\n                            |______ P prefailure warning\n\nGeneral Purpose Log Directory Version 1\nSMART           Log Directory Version 1 [multi-sector log support]\nAddress    Access  R\/W   Size  Description\n0x00       GPL,SL  R\/O      1  Log Directory\n0x01           SL  R\/O      1  Summary SMART error log\n0x02           SL  R\/O      5  Comprehensive SMART error log\n0x03       GPL     R\/O      6  Ext. Comprehensive SMART error log\n0x06           SL  R\/O      1  SMART self-test log\n0x07       GPL     R\/O      1  Extended self-test log\n0x09           SL  R\/W      1  Selective self-test log\n0x10       GPL     R\/O      1  NCQ Command Error log\n0x11       GPL     R\/O      1  SATA Phy Event Counters log\n0x80-0x9f  GPL,SL  R\/W     16  Host vendor specific log\n0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log\n0xa8-0xb7  GPL,SL  VS       1  Device vendor specific log\n0xc0       GPL,SL  VS       1  Device vendor specific log\n0xe0       GPL,SL  R\/W      1  SCT Command\/Status\n0xe1       GPL,SL  R\/W      1  SCT Data Transfer\n\nSMART Extended Comprehensive Error Log Version: 1 (6 sectors)\nDevice Error Count: 433 (device log contains only the most recent 24 errors)\n\tCR     = Command Register\n\tFEATR  = Features Register\n\tCOUNT  = Count (was: Sector Count) Register\n\tLBA_48 = Upper bytes of LBA High\/Mid\/Low Registers ]  ATA-8\n\tLH     = LBA High (was: Cylinder High) Register    ]   LBA\n\tLM     = LBA Mid (was: Cylinder Low) Register      ] Register\n\tLL     = LBA Low (was: Sector Number) Register     ]\n\tDV     = Device (was: Device\/Head) Register\n\tDC     = Device Control Register\n\tER     = Error register\n\tST     = Status register\nPowered_Up_Time is measured from power on, and printed as\nDDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,\nSS=sec, and sss=millisec. It \"wraps\" after 49.710 days.\n\nError 433 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)\n  When the command that caused the error occurred, the device was in an unknown state.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 00 01 08 00 51 00 00 40 01 00 00\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  00 91 25 43 e0 00 00 00 00 00 11 00 08     00:00:00.000  NOP [Reserved subcommand] [OBS-ACS-2]\n  00 08 00 00 30 43 96 08 d8 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n  08 b0 25 43 c5 00 08 00 30 00 11 00 08  3d+08:27:36.370  DEVICE RESET\n  00 08 00 00 30 43 9a 08 bd 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n\nError 432 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)\n  When the command that caused the error occurred, the device was in an unknown state.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 00 01 08 00 51 00 00 40 01 00 00\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  00 96 25 43 d8 00 00 00 00 00 11 00 08     00:00:00.000  NOP [Reserved subcommand] [OBS-ACS-2]\n  00 08 00 00 30 43 32 08 ce 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n  08 9a 25 43 bd 00 08 00 30 00 11 00 08  3d+08:27:34.192  DEVICE RESET\n  00 08 00 00 28 43 99 08 bd 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n\nError 431 [22] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)\n  When the command that caused the error occurred, the device was in an unknown state.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 00 01 08 00 51 00 00 40 01 00 00\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  00 32 25 43 ce 00 00 00 00 00 11 00 08     00:00:00.000  NOP [Reserved subcommand] [OBS-ACS-2]\n  00 08 00 00 30 43 b0 08 c5 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n  08 99 25 43 bd 00 08 00 30 00 11 00 08  3d+08:27:32.122  DEVICE RESET\n  00 08 00 00 20 43 99 08 bd 25 00 11 00     00:00:10.248  NOP [Abort queued commands]\n\nError 430 [21] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)\n  When the command that caused the error occurred, the device was in an unknown state.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 00 01 08 00 51 00 00 40 01 00 00\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  00 b0 25 43 c5 00 00 00 00 00 11 00 08     00:00:00.000  NOP [Reserved subcommand] [OBS-ACS-2]\n  00 08 00 00 30 43 9a 08 bd 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n  08 99 25 43 bd 00 08 00 28 00 11 00 08  3d+08:27:32.121  DEVICE RESET\n  00 08 00 00 18 43 99 08 bd 25 00 11 00     00:00:08.200  NOP [Abort queued commands]\n\nError 429 [20] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)\n  When the command that caused the error occurred, the device was in an unknown state.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 00 01 08 00 51 00 00 40 01 00 00\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  00 9a 25 43 bd 00 00 00 00 00 11 00 08     00:00:00.000  NOP [Reserved subcommand] [OBS-ACS-2]\n  00 08 00 00 28 43 99 08 bd 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n  08 99 25 43 bd 00 08 00 20 00 11 00 08  3d+08:27:32.121  DEVICE RESET\n  00 08 00 00 10 43 98 08 bd 25 00 11 00     00:00:06.152  NOP [Abort queued commands]\n\nError 428 [19] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)\n  When the command that caused the error occurred, the device was in an unknown state.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 00 01 08 00 51 00 00 40 01 00 00\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  00 89 25 42 6a 00 00 00 00 00 11 00 08     00:00:00.000  NOP [Reserved subcommand] [OBS-ACS-2]\n  00 08 00 00 30 42 d1 08 60 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n  08 a9 25 42 4d 00 08 00 30 00 11 00 08  3d+08:26:00.631  DEVICE RESET\n  00 08 00 00 30 42 22 08 45 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n\nError 427 [18] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)\n  When the command that caused the error occurred, the device was in an unknown state.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 00 01 08 00 51 00 00 40 01 00 00\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  00 d1 25 42 60 00 00 00 00 00 11 00 08     00:00:00.000  NOP [Reserved subcommand] [OBS-ACS-2]\n  00 08 00 00 30 42 37 08 58 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n  08 22 25 42 45 00 08 00 30 00 11 00 08  3d+08:25:57.929  DEVICE RESET\n  00 08 00 00 28 42 18 08 40 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n\nError 426 [17] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)\n  When the command that caused the error occurred, the device was in an unknown state.\n\n  After command completion occurred, registers were:\n  ER -- ST COUNT  LBA_48  LH LM LL DV DC\n  -- -- -- == -- == == == -- -- -- -- --\n  40 -- 00 01 08 00 51 00 00 40 01 00 00\n\n  Commands leading to the command that caused the error were:\n  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command\/Feature_Name\n  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------\n  00 37 25 42 58 00 00 00 00 00 11 00 08     00:00:00.000  NOP [Reserved subcommand] [OBS-ACS-2]\n  00 08 00 00 30 42 a9 08 4d 25 00 11 00     00:00:12.296  NOP [Abort queued commands]\n  08 18 25 42 40 00 08 00 30 00 11 00 08  3d+08:25:55.746  DEVICE RESET\n  00 08 00 00 28 42 71 08 38 25 00 11 00     00:00:10.248  NOP [Abort queued commands]\n\nSMART Extended Self-test Log Version: 1 (1 sectors)\nNum  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error\n# 1  Extended offline    Completed: read failure       90%      6629         131878391\n\nSMART Selective self-test log data structure revision number 1\n SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS\n    1        0        0  Not_testing\n    2        0        0  Not_testing\n    3        0        0  Not_testing\n    4        0        0  Not_testing\n    5        0        0  Not_testing\nSelective self-test flags (0x0):\n  After scanning selected spans, do NOT read-scan remainder of disk.\nIf Selective self-test is pending on power-up, resume after 0 minute delay.\n\nSCT Status Version:                  2\nSCT Version (vendor specific):       258 (0x0102)\nDevice State:                        Active (0)\nCurrent Temperature:                    43 Celsius\nPower Cycle Min\/Max Temperature:     --\/46 Celsius\nLifetime    Min\/Max Temperature:     --\/46 Celsius\n\nSCT Temperature History Version:     2\nTemperature Sampling Period:         1 minute\nTemperature Logging Interval:        1 minute\nMin\/Max recommended Temperature:      5\/65 Celsius\nMin\/Max Temperature Limit:            1\/70 Celsius\nTemperature History Size (Index):    128 (32)\n\nIndex    Estimated Time   Temperature Celsius\n  33    2026-09-19 20:21    43  ************************\n ...    ..( 22 skipped).    ..  ************************\n  56    2026-09-19 20:44    43  ************************\n  57    2026-09-19 20:45    44  *************************\n  58    2026-09-19 20:46    44  *************************\n  59    2026-09-19 20:47    43  ************************\n  60    2026-09-19 20:48    44  *************************\n  61    2026-09-19 20:49    44  *************************\n  62    2026-09-19 20:50    43  ************************\n  63    2026-09-19 20:51    44  *************************\n  64    2026-09-19 20:52    44  *************************\n  65    2026-09-19 20:53    43  ************************\n  66    2026-09-19 20:54    44  *************************\n  67    2026-09-19 20:55    44  *************************\n  68    2026-09-19 20:56    44  *************************\n  69    2026-09-19 20:57    43  ************************\n  70    2026-09-19 20:58    44  *************************\n ...    ..(  2 skipped).    ..  *************************\n  73    2026-09-19 21:01    44  *************************\n  74    2026-09-19 21:02    43  ************************\n  75    2026-09-19 21:03    44  *************************\n ...    ..(  7 skipped).    ..  *************************\n  83    2026-09-19 21:11    44  *************************\n  84    2026-09-19 21:12    43  ************************\n  85    2026-09-19 21:13    44  *************************\n  86    2026-09-19 21:14    44  *************************\n  87    2026-09-19 21:15    44  *************************\n  88    2026-09-19 21:16    43  ************************\n  89    2026-09-19 21:17    44  *************************\n  90    2026-09-19 21:18    44  *************************\n  91    2026-09-19 21:19    43  ************************\n  92    2026-09-19 21:20    43  ************************\n  93    2026-09-19 21:21    44  *************************\n  94    2026-09-19 21:22    43  ************************\n ...    ..( 27 skipped).    ..  ************************\n 122    2026-09-19 21:50    43  ************************\n 123    2026-09-19 21:51    42  ***********************\n 124    2026-09-19 21:52    43  ************************\n 125    2026-09-19 21:53    43  ************************\n 126    2026-09-19 21:54    43  ************************\n 127    2026-09-19 21:55    42  ***********************\n   0    2026-09-19 21:56    43  ************************\n   1    2026-09-19 21:57    42  ***********************\n   2    2026-09-19 21:58    43  ************************\n ...    ..( 29 skipped).    ..  ************************\n  32    2026-09-19 22:28    43  ************************\n\nSMART WRITE LOG does not return COUNT and LBA_LOW register\nSCT (Get) Error Recovery Control command failed\n\nDevice Statistics (GP\/SMART Log 0x04) not supported\n\nPending Defects log (GP Log 0x0c) not supported\n\nSATA Phy Event Counters (GP Log 0x11)\nID      Size     Value  Description\n0x0001  2            0  Command failed due to ICRC error\n0x000a  2           13  Device-to-host register FISes sent due to a COMRESET\n0x8000  4       326279  Vendor specific\n\n\u003c\/pre\u003e\n","brand":"Robert Elder Software Inc's Store","offers":[{"title":"Default Title","offer_id":67628252496160,"sku":"2026-10-01-WD-WMANU1372965","price":3.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0966\/8945\/5392\/files\/f2c0a833-47d2-4231-be22-ddc52abaad42.jpg?v=1790951103","url":"https:\/\/shopify.robertelder.org\/products\/500gb-western-digital-wdc-wd5000ys-01mpb0-smart-fail","provider":"Robert Elder Software Inc's Store","version":"1.0","type":"link"}