{"product_id":"500gb-seagate-st3500320as-21717-powered-on-hours","title":"500GB Seagate, ST3500320AS, (21717 Powered On Hours)","description":"\u003cp\u003e500GB, Seagate ST3500320AS, used hard drive, 7200 RPM, with 21717 powered-on hours.\u003c\/p\u003e\n\n\u003cp\u003eThe recorded SMART overall-health assessment and latest logged self-test passed. This describes the saved test results, not a guarantee of future reliability.\u003c\/p\u003e\n\n\u003ch2\u003eImportant notes\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eThis drive weighs 540 grams.\u003c\/li\u003e\n\u003cli\u003ePending sectors: 0\u003c\/li\u003e\n\u003cli\u003eReallocated sectors: 0\u003c\/li\u003e\n\u003cli\u003eLogged SMART errors: 0\u003c\/li\u003e\n\u003cli\u003eCRC errors: 0\u003c\/li\u003e\n\u003cli\u003espin_retry_count=1; disclosed as recorded, not treated by itself as a failed health assessment.\u003c\/li\u003e\n\u003cli\u003eOffline uncorrectable sectors: 0\u003c\/li\u003e\n\u003cli\u003eReported uncorrectable errors: 0\u003c\/li\u003e\n\u003cli\u003ePower cycles: 466\u003c\/li\u003e\n\u003cli\u003eSMART overall health: PASSED\u003c\/li\u003e\n\u003cli\u003eLatest Extended offline self-test: Completed without error\u003c\/li\u003e\n\u003cli\u003eBadblocks was run using the standard four-pass pattern test, and 0 bad blocks were found.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eYou will receive this specific drive, identified in this listing as serial 9QM03T80.\u003c\/p\u003e\n\n\u003cp\u003eThis used drive is sold 'as is', with no warranty on its functionality. I do warrant that the testing described in this listing was actually performed on this specific drive and that the SMART output reproduced below is the output obtained from this drive. In general, SMART data can be erased or tampered with, for example to reset the reported powered-on hours to zero. I certify that I have not erased, reset, or otherwise tampered with this drive's SMART data, but I cannot certify that a previous owner has not done so.\u003c\/p\u003e\n\n\u003cp\u003eCounters such as powered-on hours and power-cycle counts may differ slightly from the recorded output because the drive may have been powered on again between the time the SMART output was captured and packaging for shipment.\u003c\/p\u003e\n\n\u003ch2\u003eRecorded fio performance tests\u003c\/h2\u003e\n\n\u003cp\u003eThese tests were performed over a USB interface. The demonstrated transfer speeds may be artificially limited by the USB 3 interface.\u003c\/p\u003e\n\n\u003cpre\u003eSEQUENTIAL READ: bw=102MiB\/s (107MB\/s)\nSEQUENTIAL WRITE: bw=101MiB\/s (106MB\/s)\nRANDOM READ: bw=323KiB\/s (331kB\/s)\nRANDOM WRITE: bw=629KiB\/s (644kB\/s)\nRANDOM READ (Queue Depth=1): bw=313KiB\/s (321kB\/s)\u003c\/pre\u003e\n\n\u003ch2\u003eOutput from fdisk -l \/dev\/sdc\u003c\/h2\u003e\n\n\u003cpre\u003eDisk \/dev\/sdc: 465.76 GiB, 500107862016 bytes, 976773168 sectors\nDisk model: USB3.0 DISK01   \nUnits: sectors of 1 * 512 = 512 bytes\nSector size (logical\/physical): 512 bytes \/ 512 bytes\nI\/O size (minimum\/optimal): 512 bytes \/ 512 bytes\n\u003c\/pre\u003e\n\n\u003ch2\u003eOutput from hdparm -I \/dev\/sdc\u003c\/h2\u003e\n\n\u003cpre\u003e\n\/dev\/sdc:\n\nATA device, with non-removable media\n\tModel Number:       ST3500320AS                             \n\tSerial Number:      9QM03T80\n\tFirmware Revision:  SD14    \nStandards:\n\tSupported: 7 6 5 4 \n\tLikely used: 8\nConfiguration:\n\tLogical\t\tmax\tcurrent\n\tcylinders\t16383\t16383\n\theads\t\t16\t16\n\tsectors\/track\t63\t63\n\t--\n\tCHS current addressable sectors:    16514064\n\tLBA    user addressable sectors:   268435455\n\tLBA48  user addressable sectors:   976773168\n\tLogical\/Physical Sector size:           512 bytes\n\tdevice size with M = 1024*1024:      476940 MBytes\n\tdevice size with M = 1000*1000:      500107 MBytes (500 GB)\n\tcache\/buffer size  = unknown\n\tNominal Media Rotation Rate: 7200\nCapabilities:\n\tLBA, IORDY(can be disabled)\n\tQueue depth: 32\n\tStandby timer values: spec'd by Standard, no device specific minimum\n\tR\/W multiple sector transfer: Max = 16\tCurrent = ?\n\tRecommended acoustic management value: 254, current value: 0\n\tDMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 \n\t     Cycle time: min=120ns recommended=120ns\n\tPIO: pio0 pio1 pio2 pio3 pio4 \n\t     Cycle time: no flow control=120ns  IORDY flow control=120ns\nCommands\/features:\n\tEnabled\tSupported:\n\t   *\tSMART feature set\n\t    \tSecurity Mode feature set\n\t   *\tPower Management feature set\n\t   *\tWrite cache\n\t   *\tLook-ahead\n\t   *\tHost Protected Area feature set\n\t   *\tWRITE_BUFFER command\n\t   *\tREAD_BUFFER command\n\t   *\tDOWNLOAD_MICROCODE\n\t    \tSET_MAX security extension\n\t   *\t48-bit Address feature set\n\t   *\tDevice Configuration Overlay feature set\n\t   *\tMandatory FLUSH_CACHE\n\t   *\tFLUSH_CACHE_EXT\n\t   *\tSMART error logging\n\t   *\tSMART self-test\n\t    \tGeneral Purpose Logging feature set\n\t   *\t64-bit World wide name\n\t   *\tWrite-Read-Verify feature set\n\t   *\tWRITE_UNCORRECTABLE_EXT command\n\t   *\tGen1 signaling speed (1.5Gb\/s)\n\t   *\tNative Command Queueing (NCQ)\n\t   *\tPhy event counters\n\t   *\tSoftware settings preservation\n\t   *\tSMART Command Transport (SCT) feature set\n\t   *\tSCT Read\/Write Long (AC1), obsolete\n\t   *\tSCT Error Recovery Control (AC3)\n\t   *\tSCT Features Control (AC4)\n\t   *\tSCT Data Tables (AC5)\nSecurity: \n\tMaster password revision code = 65534\n\t\tsupported\n\tnot\tenabled\n\tnot\tlocked\n\tnot\tfrozen\n\tnot\texpired: security count\n\t\tsupported: enhanced erase\n\nLogical Unit WWN Device Identifier: 5000c50009a4840e\n\tNAA\t\t: 5\n\tIEEE OUI\t: 000c50\n\tUnique ID\t: 009a4840e\nChecksum: correct\n\u003c\/pre\u003e\n\n\u003ch2\u003eOutput from smartctl -x \/dev\/sdc\u003c\/h2\u003e\n\n\u003cpre\u003esmartctl 7.5 2025-04-30 r5714 [x86_64-linux-7.0.0-31-generic] (local build)\nCopyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org\n\n=== START OF INFORMATION SECTION ===\nModel Family:     Seagate Barracuda 7200.11\nDevice Model:     ST3500320AS\nSerial Number:    9QM03T80\nLU WWN Device Id: 5 000c50 009a4840e\nFirmware Version: SD14\nUser Capacity:    500,107,862,016 bytes [500 GB]\nSector Size:      512 bytes logical\/physical\nRotation Rate:    7200 rpm\nDevice is:        In smartctl database 7.5\/5706\nATA Version is:   ATA\/ATAPI-7 (minor revision not indicated)\nLocal Time is:    Tue Sep 15 03:03:27 2026 UTC\n\n==\u0026gt; WARNING: There are known problems with these drives,\nsee the following Seagate web pages:\nhttp:\/\/knowledge.seagate.com\/articles\/en_US\/FAQ\/207931en\nhttp:\/\/knowledge.seagate.com\/articles\/en_US\/FAQ\/207951en\nhttp:\/\/knowledge.seagate.com\/articles\/en_US\/FAQ\/207957en\n\nSMART support is: Available - device has SMART capability.\nSMART support is: Enabled\nAAM feature is:   Unavailable\nAPM feature is:   Unavailable\nRd look-ahead is: Enabled\nWrite cache is:   Enabled\nDSN feature is:   Unavailable\nATA Security is:  Disabled, NOT FROZEN [SEC1]\n\n=== START OF READ SMART DATA SECTION ===\nSMART Status not supported: Incomplete response, ATA output registers missing\nSMART overall-health self-assessment test result: PASSED\nWarning: This result is based on an Attribute check.\n\nGeneral SMART Values:\nOffline data collection status:  (0x82)\tOffline data collection activity\n\t\t\t\t\twas completed without error.\n\t\t\t\t\tAuto Offline Data Collection: Enabled.\nSelf-test execution status:      (   0)\tThe previous self-test routine completed\n\t\t\t\t\twithout error or no self-test has ever \n\t\t\t\t\tbeen run.\nTotal time to complete Offline \ndata collection: \t\t(  634) seconds.\nOffline data collection\ncapabilities: \t\t\t (0x7b) SMART execute Offline immediate.\n\t\t\t\t\tAuto Offline data collection on\/off support.\n\t\t\t\t\tSuspend Offline collection upon new\n\t\t\t\t\tcommand.\n\t\t\t\t\tOffline surface scan supported.\n\t\t\t\t\tSelf-test supported.\n\t\t\t\t\tConveyance Self-test supported.\n\t\t\t\t\tSelective Self-test supported.\nSMART capabilities:            (0x0003)\tSaves SMART data before entering\n\t\t\t\t\tpower-saving mode.\n\t\t\t\t\tSupports SMART auto save timer.\nError logging capability:        (0x01)\tError logging supported.\n\t\t\t\t\tGeneral Purpose Logging supported.\nShort self-test routine \nrecommended polling time: \t (   1) minutes.\nExtended self-test routine\nrecommended polling time: \t ( 106) minutes.\nConveyance self-test routine\nrecommended polling time: \t (   2) minutes.\nSCT capabilities: \t       (0x003b)\tSCT Status supported.\n\t\t\t\t\tSCT Error Recovery Control supported.\n\t\t\t\t\tSCT Feature Control supported.\n\t\t\t\t\tSCT Data Table supported.\n\nSMART Attributes Data Structure revision number: 10\nVendor Specific SMART Attributes with Thresholds:\nID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE\n  1 Raw_Read_Error_Rate     POSR--   118   099   006    -    177213299\n  3 Spin_Up_Time            PO----   095   091   000    -    0\n  4 Start_Stop_Count        -O--CK   100   100   020    -    527\n  5 Reallocated_Sector_Ct   PO--CK   100   100   036    -    0\n  7 Seek_Error_Rate         POSR--   075   060   030    -    8648801822\n  9 Power_On_Hours          -O--CK   076   076   000    -    21717\n 10 Spin_Retry_Count        PO--C-   100   100   097    -    1\n 12 Power_Cycle_Count       -O--CK   100   037   020    -    466\n184 End-to-End_Error        -O--CK   100   100   099    -    0\n187 Reported_Uncorrect      -O--CK   100   100   000    -    0\n188 Command_Timeout         -O--CK   100   099   000    -    7\n189 High_Fly_Writes         -O-RCK   100   100   000    -    0\n190 Airflow_Temperature_Cel -O---K   065   052   045    -    35 (Min\/Max 21\/37)\n194 Temperature_Celsius     -O---K   035   048   000    -    35 (0 17 0 0 0)\n195 Hardware_ECC_Recovered  -O-RC-   042   021   000    -    177213299\n197 Current_Pending_Sector  -O--C-   100   100   000    -    0\n198 Offline_Uncorrectable   ----C-   100   100   000    -    0\n199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    0\n                            ||||||_ K auto-keep\n                            |||||__ C event count\n                            ||||___ R error rate\n                            |||____ S speed\/performance\n                            ||_____ O updated online\n                            |______ P prefailure warning\n\nGeneral Purpose Log Directory Version 1\nSMART           Log Directory Version 1 [multi-sector log support]\nAddress    Access  R\/W   Size  Description\n0x00       GPL,SL  R\/O      1  Log Directory\n0x01       GPL,SL  R\/O      1  Summary SMART error log\n0x02       GPL,SL  R\/O      5  Comprehensive SMART error log\n0x03       GPL,SL  R\/O      5  Ext. Comprehensive SMART error log\n0x06       GPL,SL  R\/O      1  SMART self-test log\n0x07       GPL,SL  R\/O      1  Extended self-test log\n0x09       GPL,SL  R\/W      1  Selective self-test log\n0x10       GPL,SL  R\/O      1  NCQ Command Error log\n0x11       GPL,SL  R\/O      1  SATA Phy Event Counters log\n0x21       GPL,SL  R\/O      1  Write stream error log\n0x22       GPL,SL  R\/O      1  Read stream error log\n0x80-0x9f  GPL,SL  R\/W     16  Host vendor specific log\n0xa1       GPL,SL  VS      20  Device vendor specific log\n0xa2       GPL     VS    2248  Device vendor specific log\n0xa8       GPL,SL  VS      20  Device vendor specific log\n0xa9       GPL,SL  VS       1  Device vendor specific log\n0xb0       GPL     VS    2819  Device vendor specific log\n0xbe-0xbf  GPL     VS   65535  Device vendor specific log\n0xe0       GPL,SL  R\/W      1  SCT Command\/Status\n0xe1       GPL,SL  R\/W      1  SCT Data Transfer\n\nSMART Extended Comprehensive Error Log Version: 1 (5 sectors)\nNo Errors Logged\n\nSMART Extended Self-test Log Version: 1 (1 sectors)\nNum  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error\n# 1  Extended offline    Completed without error       00%     21716         -\n\nSMART Selective self-test log data structure revision number 1\n SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS\n    1        0        0  Not_testing\n    2        0        0  Not_testing\n    3        0        0  Not_testing\n    4        0        0  Not_testing\n    5        0        0  Not_testing\nSelective self-test flags (0x0):\n  After scanning selected spans, do NOT read-scan remainder of disk.\nIf Selective self-test is pending on power-up, resume after 0 minute delay.\n\nSCT Status Version:                  3\nSCT Version (vendor specific):       522 (0x020a)\nDevice State:                        Active (0)\nCurrent Temperature:                    35 Celsius\nPower Cycle Min\/Max Temperature:     21\/39 Celsius\nLifetime    Min\/Max Temperature:     17\/48 Celsius\nUnder\/Over Temperature Limit Count:   0\/426\n\nSCT Temperature History Version:     2\nTemperature Sampling Period:         1 minute\nTemperature Logging Interval:        1 minute\nMin\/Max recommended Temperature:      0\/ 0 Celsius\nMin\/Max Temperature Limit:            0\/ 0 Celsius\nTemperature History Size (Index):    128 (56)\n\nIndex    Estimated Time   Temperature Celsius\n  57    2026-09-15 00:56    34  ***************\n ...    ..( 47 skipped).    ..  ***************\n 105    2026-09-15 01:44    34  ***************\n 106    2026-09-15 01:45    35  ****************\n ...    ..( 32 skipped).    ..  ****************\n  11    2026-09-15 02:18    35  ****************\n  12    2026-09-15 02:19    36  *****************\n ...    ..( 11 skipped).    ..  *****************\n  24    2026-09-15 02:31    36  *****************\n  25    2026-09-15 02:32    35  ****************\n ...    ..( 15 skipped).    ..  ****************\n  41    2026-09-15 02:48    35  ****************\n  42    2026-09-15 02:49    36  *****************\n  43    2026-09-15 02:50    35  ****************\n  44    2026-09-15 02:51    35  ****************\n  45    2026-09-15 02:52    37  ******************\n ...    ..(  5 skipped).    ..  ******************\n  51    2026-09-15 02:58    37  ******************\n  52    2026-09-15 02:59    36  *****************\n  53    2026-09-15 03:00    35  ****************\n ...    ..(  2 skipped).    ..  ****************\n  56    2026-09-15 03:03    35  ****************\n\nSMART WRITE LOG does not return COUNT and LBA_LOW register\nSCT (Get) Error Recovery Control command failed\n\nDevice Statistics (GP\/SMART Log 0x04) not supported\n\nPending Defects log (GP Log 0x0c) not supported\n\nSATA Phy Event Counters (GP Log 0x11)\nID      Size     Value  Description\n0x000a  2           11  Device-to-host register FISes sent due to a COMRESET\n0x0001  2            0  Command failed due to ICRC error\n0x0003  2            0  R_ERR response for device-to-host data FIS\n0x0004  2            0  R_ERR response for host-to-device data FIS\n0x0006  2            0  R_ERR response for device-to-host non-data FIS\n0x0007  2            0  R_ERR response for host-to-device non-data FIS\n\n\u003c\/pre\u003e\n","brand":"Robert Elder Software Inc's Store","offers":[{"title":"Default Title","offer_id":67628251316512,"sku":"2026-10-01-9QM03T80","price":11.27,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0966\/8945\/5392\/files\/cde2c835-5570-4634-8585-10ae813bb89c.jpg?v=1790950994","url":"https:\/\/shopify.robertelder.org\/products\/500gb-seagate-st3500320as-21717-powered-on-hours","provider":"Robert Elder Software Inc's Store","version":"1.0","type":"link"}